Lift Chains

The life of lift chains on lift trucks can be prolonged completely with proper care and maintenance. Like for instance, correct lubrication is actually the most efficient method in order to extend the service capability of this part. It is vital to apply oil periodically utilizing a brush or whichever lube application device. The frequency and volume of oil application must be adequate to be able to stop any rust discoloration of oil in the joints. This reddish brown discoloration normally signals that the lift chains have not been correctly lubricated. If this situation has occurred, it is very important to lubricate the lift chains as soon as possible.

During lift chain operation it is normal for some metal to metal contact to occur that can cause several parts to wear out sooner or later. When there is 3 percent elongation on the lift chain, it is considered by industry standards to have worn out the chain. In order to avoid the scary chance of a catastrophic lift chain failure from occurring, the manufacturer highly suggests that the lift chain be replaced before it reaches three percent elongation. The lift chain gets longer because of progressive joint wear which elongates the chain pitch. This elongation could be measured by placing a certain number of pitches under tension.

Another factor to ensuring correct lift chain maintenance is to check the clevis pins on the lift chain for signs of wear and tear. The lift chains have been assembled so that the tapered faces of the clevis pin are lined up. Usually, rotation of the clevis pins is frequently caused by shock loading. Shock loading happens if the chain is loose and then suddenly a load is applied. This causes the chain to experience a shock as it 'snaps' under the load tension. With no correct lubrication, in this particular case, the pins can rotate in the chain's link. If this situation takes place, the lift chains need to be replaced right away. It is vital to always replace the lift chains in pairs in order to ensure even wear.


Click to Download the pdf

Forklift Parts in Fresno

Alternators

An alternator is a machine which changes mechanical energy into electric energy. It does this in the form of an electrical current. In essence, an AC electric generator could be labeled an alternator. The word usually refers to a rotating, small machine driven by automotive and other internal combustion engines. Alternators which are situated in power stations and are powered...

More

---

Brakes

A brake in which the friction is supplied by a set of brake shoes or brake pads which press against a rotating drum shaped unit referred to as a brake drum. There are several particular differences among brake drum kinds. A "brake drum" is normally the definition provided if shoes press on the inner exterior of the drum. A "clasp...

More

---

Carriage Rollers

Specially designed bearings known as carriage rollers are regularly seen on lift masts because they enable them to operate better in difficult environmental surroundings. The typical lift mast is often subject to frequent oscillations, shocks, static loads, and vibrations and high dynamics. This apparatus is regularly exposed to environmental influences like for instance heat, dust, cold, aggressive ambient air, moisture...

More

---

Carriages and Carriage Parts

Rated by the fork carriage lifting capacity, there are actually four sizes of hook type blade carriages. The hook type fork carriages have been standardized. The carriage bar spacing utilized for Class 1 is around thirteen inches and the Class 1 carriage is rated to hold cargo as much as 2000lbs. The Class 2 carriage is rated to carry cargo...

More

---

Control Valves

Automatic control systems were first developed more than two thousand years ago. The ancient water clock of Ktesibios in Alexandria Egypt dating to the third century B.C. is thought to be the very first feedback control machine on record. This clock kept time by means of regulating the water level in a vessel and the water flow from the vessel....

More

---

Controllers

Lift trucks are obtainable in several different models which have various load capacities. Most standard forklifts utilized inside warehouse environment have load capacities of one to five tons. Larger scale units are utilized for heavier loads, like for instance loading shipping containers, may have up to 50 tons lift capacity. The operator could use a control so as to lower...

More

---

Differentials

A mechanical device capable of transmitting rotation and torque through three shafts is known as a differential. Every now and then but not always the differential will utilize gears and would operate in two ways: in cars, it receives one input and provides two outputs. The other way a differential works is to put together two inputs in order to...

More

---

Drive Axles

A forklift drive axle is a piece of equipment which is elastically fastened to a vehicle framework using a lift mast. The lift mast is connected to the drive axle and could be inclined around the axial centerline of the drive axle. This is accomplished by no less than one tilting cylinder. Forward bearing parts along with back bearing parts...

More

---