Fuel Systems

The fuel systems task is to provide your engine with the gasoline or diesel it needs in order to run. If any of the fuel system parts breaks down, your engine will not work correctly. There are the main parts of the fuel system listed under:

Fuel Tank: The fuel tank is a holding cell intended for your fuel. When filling up at a gas station, the fuel travels downward the gas hose and into your tank. Inside the tank there is a sending unit. This is what tells the gas gauge how much gas is within the tank.

Fuel Pump: In newer cars, the majority contain fuel pumps normally located inside the fuel tank. Several of the older automobiles will connect the fuel pump to the engine or placed on the frame next to the tank and engine. If the pump is on the frame rail or inside the tank, then it is electric and runs with electricity from your cars' battery, whereas fuel pumps which are connected to the engine use the motion of the engine to be able to pump the fuel.

Fuel Filter: For overall engine life and performance, clean fuel is essential. The fuel injector is made up of small holes that clog with no trouble. Filtering the fuel is the only way this can be avoided. Filters can be found either before or after the fuel pump and in several instances both places.

Fuel Injectors: Most domestic cars made after the year 1986, came from the factory with fuel injection. A computer control opens the fuel injectors so as to allow fuel into the engine, which replaced the carburator who's task originally was to carry out the mixing of the fuel and air. This has caused lower emission overall and better fuel economy. The fuel injector is essentially a small electric valve which closes opens with an electric signal. By injecting the fuel close to the cylinder head, the fuel stays atomized, or within small particles, and can burn better when ignited by the spark plug.

Carburetors: Carburetors have the task of taking the fuel and mixing it with the air without whichever intervention from a computer. Carburetors require regular tuning and rebuilding though they are easy to operate. This is one of the main reasons the newer vehicles on the market have done away with carburetors instead of fuel injection.

Click to Download the pdf

Forklift Parts in Fresno

Alternators

An alternator is a machine which changes mechanical energy into electric energy. It does this in the form of an electrical current. In essence, an AC electric generator could be labeled an alternator. The word usually refers to a rotating, small machine driven by automotive and other internal combustion engines. Alternators which are situated in power stations and are powered...

More

---

Brakes

A brake in which the friction is supplied by a set of brake shoes or brake pads which press against a rotating drum shaped unit referred to as a brake drum. There are several particular differences among brake drum kinds. A "brake drum" is normally the definition provided if shoes press on the inner exterior of the drum. A "clasp...

More

---

Carriage Rollers

Specially designed bearings known as carriage rollers are regularly seen on lift masts because they enable them to operate better in difficult environmental surroundings. The typical lift mast is often subject to frequent oscillations, shocks, static loads, and vibrations and high dynamics. This apparatus is regularly exposed to environmental influences like for instance heat, dust, cold, aggressive ambient air, moisture...

More

---

Carriages and Carriage Parts

Rated by the fork carriage lifting capacity, there are actually four sizes of hook type blade carriages. The hook type fork carriages have been standardized. The carriage bar spacing utilized for Class 1 is around thirteen inches and the Class 1 carriage is rated to hold cargo as much as 2000lbs. The Class 2 carriage is rated to carry cargo...

More

---

Control Valves

Automatic control systems were first developed more than two thousand years ago. The ancient water clock of Ktesibios in Alexandria Egypt dating to the third century B.C. is thought to be the very first feedback control machine on record. This clock kept time by means of regulating the water level in a vessel and the water flow from the vessel....

More

---

Controllers

Lift trucks are obtainable in several different models which have various load capacities. Most standard forklifts utilized inside warehouse environment have load capacities of one to five tons. Larger scale units are utilized for heavier loads, like for instance loading shipping containers, may have up to 50 tons lift capacity. The operator could use a control so as to lower...

More

---

Differentials

A mechanical device capable of transmitting rotation and torque through three shafts is known as a differential. Every now and then but not always the differential will utilize gears and would operate in two ways: in cars, it receives one input and provides two outputs. The other way a differential works is to put together two inputs in order to...

More

---

Drive Axles

A forklift drive axle is a piece of equipment which is elastically fastened to a vehicle framework using a lift mast. The lift mast is connected to the drive axle and could be inclined around the axial centerline of the drive axle. This is accomplished by no less than one tilting cylinder. Forward bearing parts along with back bearing parts...

More

---